Download Article

Download Article

Rust isn't just an eyesore—it tin also slow your board and concord you back during a fun day outside.[1] Don't worry! This is a really common trouble that a lot of snowboarders deal with, and it'southward really easy to fix. With a few elementary tools, y'all tin get rid of pesky rust and metal burrs and so you lot'll be gear up to hit the slopes!

  1. 1

    Prop your snowboard on top of a vise or other support. Identify your board in a big, open workspace, where yous have plenty of room to inspect and tune upward the edges. You don't need to secure or spike annihilation in place—just set your board binding-side-down on elevation of the table vises, so y'all tin can easily achieve and polish your board edges.[2]

    • It's okay if you don't have table vises! Two stacks of books can as well go the chore washed while you work.
    • You tin also prop up your snowboard on 2 wood blocks.[3]

  2. 2

    Glide a towel along your edges to find rust and burrs. Grab a basic hand towel and slide it slowly along your board's edges. Feel for any precipitous edges or sections—these are certain signs of burrs or rust spots.[4]

    • The burrs will snag and pull off small fibers from your towel, which volition brand them easy to discover again on your board.

    Advertisement

  3. iii

    Polish away burrs with a diamond stone and rubbing alcohol. Spritz rubbing booze on the surface of a diamond stone—this is a rough, sandpaper-similar rock that helps buff your edges. Hold the diamond stone parallel to the board, dragging information technology along the metal border. Movement in polish motions, working from tip to tail as you sand away the burs. Don't identify the stone flush with the edge—instead, keep it parallel every bit you work, and then you can really focus on smoothing out the metal.[5]

    • You can notice diamond stones online, or at almost sports goods stores. These are bang-up for smoothing away imperfections from the sides of your snowboard.

  4. 4

    Elevate a gluey stone from tip to tail along the sides of the board. Grab a gummy stone—this is a firm, abrasive, eraser-like rock that will work away some of the rust on your lath.[6] Agree the ends of the gummy stone with both hands, placing it snugly forth the sparse edge of your board. Run the gluey stone downwards your board'southward edge from tip to tail, working away any rust as you go.[7]

    • If yous don't have a viscous rock, use fine- or medium-grit sandpaper instead.[8]
    • If you have really extensive rust, a apartment file can get the job done. Place the file flat on height the lath and drag it back and along along the edge, moving from tip to tail.[nine]

  5. 5

    Sand down the side edges with a diamond rock one time over again. Grab your diamond stone again, placing information technology flush on the lath'southward edge. Don't press on the stone—instead, agree it at a slightly upward angle, using your fingers to guide the stone forth the edge.[10]

    • This prevents the diamond stone from damaging the rest of the board.

  6. 6

    Go over the edges 1 more time with the viscous rock. Pick up your gummy stone and place it directly on board'southward border again, but like you did before. Move the mucilaginous stone from tip to tail to become rid of any pesky, leftover rust from your board.[eleven]

  7. 7

    Wipe downwardly your lath with a clean rag and some rubbing alcohol. Spritz a clean towel with rubbing alcohol and drag it forth the edges of your snowboard. Wipe abroad any pocket-size bits of metal that've collected on your board, so your equipment is squeamish and clean.[12]

    8. Advertisement

  1. one

    Bring your snowboard inside instead of leaving information technology out in the snow. Water and rust are all-time friends—so, when you lot leave your snowboard outside, you lot're actually exposing it to a lot of frozen water and potential rust. Instead, place in a clean, dry surface area so rust doesn't form on your lath over time.[13]

  2. 2

    Dry off your snowboard each fourth dimension y'all use it. Go along a clean towel handy whenever yous go snowboarding. Wipe down your entire lath and then there'southward no leftover moisture, which is a recipe for rust.[fourteen]

    • If you drive out to the slopes a lot, keep a clean towel stashed somewhere in your car.

  3. 3

    Wax your snowboard when you put information technology away for the season. Grab a make clean towel and wipe away any leftover wet from the slopes. Melt a cube of snowboard wax over the surface of your board earlier putting it away for good. Don't scrape it off until next winter—this will keep your equipment protected during the warmer months.[15]

  4. 4

    Don't keep your snowboard on the superlative of your auto. When y'all bulldoze to the slopes, go along your snowboard inside your car instead of on meridian of it. Although car racks are convenient, they'll expose your board to a lot of wetness, open up air, and route common salt.[16]

    5. Advertising

Ask a Question

200 characters left

Include your electronic mail accost to get a message when this question is answered.

Submit

Advertisement

  • If you see a small, small-scale rust spot, wipe it down with a moisture cloth. If the rust isn't besides severe, information technology might wipe off pretty easily.[17]

  • Take your snowboard to a tune-up shop if you don't have a lot of tune-up experience. They can polish your edges and easily get rid of any rust![18]

Thanks for submitting a tip for review!

Advertisement

Things You'll Need

  • Vise table
  • Make clean rags
  • Rubbing alcohol
  • Diamond stone
  • Gummy stone
  • Sandpaper (optional)
  • Make clean rags
  • Snowboard wax
  • Iron

References

About This Article

Thanks to all authors for creating a folio that has been read 13,646 times.

Did this article help you?